Futaba 10CP (T10CHP) - 10 Channel 2.4GHz TX with 14 Channel R6014FS RX

The brand new 10CP (T10CHP) 2.4GHz system that offers the impossible: Pro-level features at a sport-system price!

Some people feel that a 2.4GHz system with a built-in module will always offer better response than a modular system. Nothing could be further from the truth.

The 10C is a modular system, yet offers response superior to most "dedicated" systems. Why? Because response doesn't depend on whether your module is built-in or modular. It depends on whether your signal starts in analog or digital form.

Converting a signal from analog to digital form requires processing time - what you experience as lag. The 10C, on the other hand, was designed with a totally digital data stream. The signal starts digital and stays digital. Since no additional processing is needed, there's no lag either, just virtually instantaneous, real-time response.

And because the 10C is modular, you can use the TM-10 module to fly 2.4GHz-equipped aircraft…or replace it with a 35, 50 or 72MHz module, and fly existing models without added equipment or expense.

Set Includes:
Futaba 10CP (T10CHP) - 10 Channel 2.4GHz TX (Mode 2 - Left throttle) x 1
R6014FS - 14 Channel 2.4GHz RX x 1
Futaba S3152 high torque digital servos x 4
Rechargeable transmitter and receiver packs
Mains charger

Compatible Receivers:
7ch Mode: R607FS/R616FFM/R617FS (Via screen selection)
10ch Mode: R608FS/R6014FS

Standard Programming Functions:
Big, 160 x 72 LCD with backlighting, adjustable contrast & auto-off
Dial 'n' Key™ programming w/joystick navigation
15-Model memory (expandable w/optional CamPACs)
10-character user name
10-character model name
2048 resolution in FASST 10-channel mode
Basic & Advanced menus
Enhanced airplane, heli & glider software
Smart Switch Technology™ (SST) — Logic Switches allow you to activate a function when specified switch and/or stick positions occur
Up/down on/off timer (activate by stick or switch)
Tracks service hours for radio and models
Mode 1-4 selectable (Modes 3 & 4 programmable)
Assignable functions/switches
Auxiliary channel screen - for 1-step function/switch assignment & eliminating unused auxiliary functions
2 proportional slider switches
Digital trims on all 4 main channels
Trim memory & sub-trims (all channels)
Adjustable trim steps (1-40)
Fail-safe, servo reversing & EPA
"Full Functionality" trainer system (cord required)
Flap switch (3-position)
Retract switch
Rotary Dial (3)
Adjustable Throttle Cut/Idle Down
Sticks w/length & tension adjustments
Servo cycle w/bar graph displays
Constant trim, voltage, name and timer display
themodelhelistore.com

Helicopter Specific:
The 10C accepts separate gyro sensitivity, governor speed and servo travel rates for up to 4 flight modes - and automatically changes all three when the flight mode changes.

6 Programmable Mixes (4 linear/ (2) 5-point curves) 8 Factory-Defined Mixes: Hover-Throttle; Hover-Pitch; Throttle-Needle; Governor; Offset; Revo (5-pt.); Delay; and Throttle Mix (ail/ele/rdr)
Gyro menu
8 swash plate types w/graphics
Swash Plate AFR
(4) 7-point throttle curves and (5) (including throttle hold) 7-point pitch curves
Adjustable High/Low pitch setting
3 Adjustable Idle-up conditions

S3152 High Torque Digital Servo Specifications:

Metric		Imperial
Volts Torque Speed 4.8 4.9 Kg.cm 0.22 sec sec/60° 6.0 6.2 Kg.cm 0.18 sec/60° Dimensions - mm Weight 41 x 20 x 38 42g		Volts Torque Speed 4.8 69 oz.in 0.22 sec/60° 6.0 87 oz.in 0.18 sec/60° Dimensions - inches Weight 1.6 x 0.8 x 1.5 1.5oz
Further Information
Type Motor Type Bearing Type Digital 3 Pole Ball Bearing